Your Universal Remote Control Center
RemoteCentral.com
Weemote Kids' Remote Control Review
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Programming Guide:

To program a TV or STB code: Press and hold the [TV] (& TV/VCR) or [STB] (Cable/Sat/PVR) button for three seconds until the LED begins to blink. Enter the code using the [100], [10] and [1] buttons. For "123", press [100] once, [10] twice and [1] three times. Press [TV] or [STB] to save. The LED will flash three times to confirm. Test your code using the Power button. If it does not work, perform these steps again.

To search for a code: Press and hold the [TV] or [STB] button for three seconds until the LED begins to blink. Press the [VOLUME UP] button once every half second or so to test each code. You may need to push the button more than 100 times. When you have searched through all codes the LED will blink twice. To reverse, using [VOLUME DOWN]. To save the correct code, press [TV] or [STB]. The LED will blink three times to confirm.

To blink back the configured code: Press and hold the [TV] or [STB] button for three seconds until the LED begins to blink. Press [TV] or [STB] again. The code will be blinked back the number of hundreds, pause, number of tens, pause, then number of ones.

To remove a TV or STB codes: Press and hold the [TV] or [STB] button for three seconds until the LED begins to blink. Enter the code "333" using the [100], [10] and [1] buttons. Press [TV] or [STB] to confirm. The LED will blink three times to confirm.

To program a favorite channel: Press and hold the [FAV] button for three seconds until the led begins to blink. Press the favorite channel button you would like to program (or [MUTE] if you want to add a sixth channel), then enter the code using the [100], [10] and [1] buttons. For "47", press [10] twice and [1] three times. Press the [FAV] button to save. The LED will blink three times to confirm.

(Weemote 2:) To program favorite channels 7 through 10: Press and hold the [FAV] button for three seconds until the led begins to blink. Press the gray [MUTE] button. Press the favorite channel button you would like to program - for Channel 7 press [2], for Channel 8 press [3], for Channel 9 press [4] and for Channel 10 press [5]. Now enter the code using the [100], [10] and [1] buttons as above. Press the [FAV] button to save. The LED will blink three times to confirm.

To delete a favorite channel button: Press and hold the [FAV] button for three seconds until the led begins to blink. Press the favorite channel button you want to delete, or [MUTE] if you want to reset it. The LED will blink three times to confirm.

(Weemote:) To set channel 3 or 4 for your set top box: Press and hold the [TV] button for three seconds until the led begins to blink. Press the [CHANNEL UP] button once. Press the big number [3] or [4] button to select the correct channel. The LED will blink twice.

(Weemote 2:) To set channel 2, 3, 4, 5 or Input for your set top box: Press and hold the [TV] button for three seconds until the led begins to blink. Press the [CHANNEL UP] button once. Press the big number [1] for Video Input, or the [2], [3], [4] or [5] button to select the correct channel. The LED will blink twice.

To add the "Enter" function to favorite channel macros: Press and hold the [TV] or [STB] button for three seconds until the LED begins to blink. Press the [FAV] button once. Press the number [1] button. The LED will blink twice. To clear this option, change [TV] or [STB] codes.

To add the forced 3-digit option: Press and hold the [TV] or [STB] button for three seconds until the LED begins to blink. Press the [FAV] button once. Press the [100] button. The LED will blink twice. To clear this option, change [TV] or [STB] codes.

(Weemote 2:) To adjust transmission speed: Press and hold the [FAV] button for three seconds until the led begins to blink. Press the [TV] button once. Enter a number from 1 through 100 using the [100], [10] and [1] buttons, where 1 is fastest and 100 is slowest (5 to 10 is normal). Press [TV] to confirm. The LED will blink three times.

(Weemote 2:) To power-on to the first favorite channel: Press and hold the [TV] button for three seconds until the led begins to blink. Press the red [POWER] button once. The LED will blink three times.

(Weemote 2:) To disable the volume keys: Press and hold the [TV] button for three seconds until the led begins to blink. Press the [FAV] button once. Press the number [10] button. The LED will blink three times.

(Weemote 2:) To disable the channel keys: Press and hold the [TV] button for three seconds until the led begins to blink. Press the [FAV] button once. Press the number [1] button. The LED will blink three times.

(Weemote Sr/3:) To allow free channel roaming: Press and hold the [TV] button for three seconds until the led begins to blink. Press the [FAV] button once. Press the number [2] button. The LED will blink three times.

(Weemote Sr/3:) To disable STB power off: Press and hold the [STB] button for three seconds until the led begins to blink. Enter the code "950" using the [100], [10] and [1] buttons. Press [STB] to confirm. The LED will blink three times.

To reset the remote: Press and hold the [TV] button for three seconds until the LED begins to blink. Enter the code "999" using the [100], [10] and [1] buttons. Press [TV] to confirm. The LED will blink twice and the remote is reset.

Previous PagePrevious page
Continue to codes page 1Next Page

Hosting Services by ipHouse