Your Universal Remote Control Center
RemoteCentral.com
Home Logic UR362 Remote Control Review
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Home Logic UR362 Programming Guide:

To set the clock: Press [EDIT], then [TIME/DATE]. Press [UP] and [DOWN] to change the value, and [LEFT] or [RIGHT] to select the next item. Press [EDIT] to save.

To learn signals: Press [LEARN]. Select the device you would like to learn under. Press a button and then hold the source button on your original remote until the display reads "OK". If it shows "ERROR" it was unable to capture the code; "NO DATA" means it could not see any infrared activity. Press [LEARN] to save.

To learn on multi-code keys: Follow the directions above to learn a signal on [S1] through [S5] or the [POWER] button. To learn the second signal select the button again, and again for the third, fourth and fifth signals. Note that you cannot change a single learned entry; you will need to start over from the beginning. Press [LEARN] to save.

To record a macro: Press [LEARN] and then the [MACRO] button. Select a button to place the macro on – any component button or [0] through [8] and [+10]. Now, navigate the remote and enter the sequence of commands you would like. Note that changing devices counts as 1 out of a possible 20 steps. To add a delay, hold the button you would like the delay after. A counter at the top of the screen will start at 1 and go up to 99 – release the button when you reach the desired delay length. Press [LEARN] to save. It is also possible to record up to five macros on a multi-code button by pressing the button multiple times, however note that all macros on that button will play back in sequence.

To use a macro: Press the [MACRO] button. The screen will read "MACRO?". Now press the component or keypad button which contains your macro.

To add an alarm: Press [EDIT], then [ON/OFF ALARM]. Press [UP] and [DOWN] to change the value, and [LEFT] or [RIGHT] to select the next item. Press [EDIT] to save. After you have set the desired time, press [EDIT] to save the alarm as a timed buzzer, or press [RIGHT] followed by a macro button to save it as a timed macro.

To enable/disable alarms: Press the [ON/OFF ALARM] button. When alarms are enabled a small clock icon will appear on-screen.

To set a sleep timer: Select the device you would like to turn off and then press the [SLEEP] button. On the first button press the timer will be set to 15 minutes, press again to scroll through 30, 45 and 60 minutes, and once again to disable. After a timer has been set you may check the remaining time by pressing the [SLEEP] button. Press the [SLEEP] button multiple times to lengthen the amount of time or disable it.

To select label pages: Press the [LANG] button. The screen will read "PAGE 1" or "PAGE 2". Note that it is recommended to edit the values on Page 2 only.

Character Map
Complete character list.
To edit button labels: Select the device you would like to change labels on. Press [EDIT] and then press the user or component button you would like to edit the label of. Press [UP] and [DOWN] to change the value, and [LEFT] or [RIGHT] to select the next position. Press [ENTER] to clear a position or add a space. Press [EDIT] to save. All names will be auto-centered.

To edit multi-code button labels: Follow the directions above to edit the first label on a multi-code key. Each time you press the multi-code button the unit will step to the next label.

To enable or disable the beep tone: Press the [AUDIO] button. When the beep tone is enable a small musical note symbol will be displayed on-screen.

To clear a button: Select the component which contains a button you want to erase. Press the [CLEAR] button followed by the desired button. "OK!" appears on-screen.

To clear all data for a device: Press the [CLEAR] button followed by the component you would like to erase. "CLEARING" appears on-screen followed by "OK!".

To clear a macro: Press the [CLEAR] button followed by [MACRO] and the component or keypad button containing the macro you want to erase. "OK!" appears on-screen.

To reset the clock: Press the [RESET] button.

Low battery symbol: If the low battery icon stays lit on-screen it is recommended you soon replace the remote’s batteries. If the icon is flashing the remote will refuse to operate until you replace the batteries.

Previous PagePrevious page
Continue to the message forumNext Page

Hosting Services by ipHouse