Your Universal Remote Control Center
RemoteCentral.com
Audio, Receivers & Speakers Forum - View Post
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Page 3 of 3
Topic:
Setting Sub Level Using Avia DVD
This thread has 33 replies. Displaying posts 31 through 34.
Post 31 made on Saturday December 22, 2001 at 08:08
Bruce Burson
Founding Member
Joined:
Posts:
October 2001
897
disregard - hit the "Submit" button before I was ready.

This message was edited by Bruce Burson on 12/22/01 09:33.00.
Never confuse your career with your life.
Post 32 made on Saturday December 22, 2001 at 09:01
Bruce Burson
Founding Member
Joined:
Posts:
October 2001
897
disregard again, maybe I'll be able to get it right the third time...

This message was edited by Bruce Burson on 12/22/01 09:40.34.
Never confuse your career with your life.
Post 33 made on Saturday December 22, 2001 at 09:27
Bruce Burson
Founding Member
Joined:
Posts:
October 2001
897
ttiger,

In response to your question on the previous page (what speakers and amplification am I using for my Large channels?):

My mains are Cerwin-Vega! AT-100s: I bought them in 1989, so I'm not sure I remember the specs. Each has a 1" tweeter, two 4.5" mids, and a 15" (!) woofer in a back-ported cabinet, and (I think) is rated to 400W.

The unpowered subwoofer is part of a Cerwin-Vega! HTE-10 matched 5.1 set in 1997. It has two 10" drivers in a front-ported cabinet, and is wired for L & R channels as well as having a pass-through for two satellites. (I think) it's rated at 250W per channel.

BTW, I use the four satellites from the same set as my surrounds. The center speaker flunked WAF, so that channel is currently fed into the TVs integral amp and speakers (Pioneer SD-T50W1, if you're interested).

Until a month ago, I powered the speakers using three NAD PE2200. Two were each bridged into 700W mono for the two mains. I ran a Y adaptor from the subwoofer output on my receiver into the third, unbridged at 400W per channel stereo for the two sub inputs.

That was my "stereo audio & Pro Logic" setup. In the last few weeks I've finally entered the modern world of Dolby Digital/DTS/THX, where all channels are theoretically amplified the same... So the current setup is as follows: A Kenwood KRF-X7775D THX Select receiver delivers up to 180W each into the "main" five channels (or would if I wasn't using the TV to drive the center). The sub is wired into the L & R surrounds, passing through to the satellites on those channels.

BTW, the KRF-X7775D only provides five channels of amplification, so I added a Kenwood KMF-X9000 THX Ultra amp (130W per channel) to power the two rear center speakers.

So each of my four Large channels can get up to 180W. At my listening levels, I can shake the room and invite my neighbors over to watch the movie. :) Even though the amps are underrated for the speakers I have noticed absolutely no clipping at any level I care to drive them to, so I'm happy.

And there's no doubt in my ears (grin) that the 15" woofers produce bigger & better bass than the 10" sub does...

-Bruce

This message was edited by Bruce Burson on 01/13/02 08:36.59.
Never confuse your career with your life.
Post 34 made on Saturday December 22, 2001 at 13:01
Matt
Founding Member
Joined:
Posts:
August 2001
1,802
All in all it's what you like, not what's 'proper'.

Page 3 of 3


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse