Your Universal Remote Control Center
RemoteCentral.com
Complete Control by URC Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
MX-151 Source Select with rs 232
This thread has 8 replies. Displaying all posts.
Post 1 made on Sunday August 29, 2021 at 12:05
icarusd
Long Time Member
Joined:
Posts:
September 2006
54
I'm struggling to directly access my sources through the serial port. Using CCP and according to the guidelines from McIntosh it should be !SRC and then the source number. Have tried everything and I'm sure it's something simple (or stupid) that I'm missing. Everything else works great, and I can access the sources just fine using the IR data, it's just a little janky to have a flasher on the front of this gorgeous piece of equipment.

Thanks in advance for any help.

-Derek
Icarus D
Post 2 made on Sunday August 29, 2021 at 21:33
Brad Humphrey
Super Member
Joined:
Posts:
February 2004
2,649
What base station are you using to send the RS232 strings?

By the way, that model has an IR jack on the back. So you do not need an IR flasher on the front either.

Last edited by Brad Humphrey on August 29, 2021 21:41.
OP | Post 3 made on Monday August 30, 2021 at 09:12
icarusd
Long Time Member
Joined:
Posts:
September 2006
54
Hello Brad,

I'm using a MRX-2. Good point on the IR in jack. Absolutely everything else works but those direct source commands.

Derek
Icarus D
Post 4 made on Monday August 30, 2021 at 12:42
Brad Humphrey
Super Member
Joined:
Posts:
February 2004
2,649
So you are trying to program the CCP app to control RS232? Or do you have an old MX-5000 or KP-4000?
Those 3 products are the only way to use the serial ports in CCP.

Have you tried using the RS232 codes for McIntosh in CCP? Code 1236?

Also, default Baud Rate on the MRX-2 is 9600. The McIntosh wants 115200. So you need to click on the serial port properties in CCP and change that.
OP | Post 5 made on Monday August 30, 2021 at 13:42
icarusd
Long Time Member
Joined:
Posts:
September 2006
54
I'm so stupid, it works fine and the answer was right there on the docs from McIntosh. All good now, thanks again for the help.

D

Last edited by icarusd on August 30, 2021 14:07.
Icarus D
Post 6 made on Monday August 30, 2021 at 20:56
goldenzrule
Loyal Member
Joined:
Posts:
July 2007
8,482
On August 30, 2021 at 12:42, Brad Humphrey said...
So you are trying to program the CCP app to control RS232? Or do you have an old MX-5000 or KP-4000?
Those 3 products are the only way to use the serial ports in CCP.

Have you tried using the RS232 codes for McIntosh in CCP? Code 1236?

Also, default Baud Rate on the MRX-2 is 9600. The McIntosh wants 115200. So you need to click on the serial port properties in CCP and change that.

What about the MX-6000?
Post 7 made on Tuesday August 31, 2021 at 00:17
Brad Humphrey
Super Member
Joined:
Posts:
February 2004
2,649
On August 30, 2021 at 20:56, goldenzrule said...
What about the MX-6000?

Well, if you can get it to connect to CCP then that would work too.

I had a like new MX6000 last year a customer gave me. I tried everything I could to get it to connect and it just wouldn't. A few of those tricks I tried came from here at RC.
In the end, it seemed the only way to get it to work was using an old version of Windows and I no longer have access to anything like that. So I tossed it (made me sad).

Come to think of it, doesn't the MX5000 have the same connection issues (needing a certain version of Windows, Sync, or something)?
Post 8 made on Tuesday August 31, 2021 at 07:42
goldenzrule
Loyal Member
Joined:
Posts:
July 2007
8,482
On August 31, 2021 at 00:17, Brad Humphrey said...
Well, if you can get it to connect to CCP then that would work too.

I had a like new MX6000 last year a customer gave me. I tried everything I could to get it to connect and it just wouldn't. A few of those tricks I tried came from here at RC.
In the end, it seemed the only way to get it to work was using an old version of Windows and I no longer have access to anything like that. So I tossed it (made me sad).

Come to think of it, doesn't the MX5000 have the same connection issues (needing a certain version of Windows, Sync, or something)?

I don't know. I will go back 10 years in a time machine, and then from that point try to remember back :-/
Post 9 made on Tuesday August 31, 2021 at 22:16
tomciara
Loyal Member
Joined:
Posts:
May 2002
8,044
On August 31, 2021 at 00:17, Brad Humphrey said...
Come to think of it, doesn't the MX5000 have the same connection issues (needing a certain version of Windows, Sync, or something)?

I tried to make an MX 5000 work with RS 232 and it was a constant service call. I put in quite a few of those remotes, but I always used them in RF and IR modes.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse