|
|
|
Custom Installers' Lounge Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
Only odd transponders are coming in
| |
|
Topic: | Only odd transponders are coming in This thread has 17 replies. Displaying posts 1 through 15. |
|
Post 1 made on Thursday December 12, 2002 at 13:27 |
john mulgrew Long Time Member |
Joined: Posts: | July 2002 114 |
|
|
on the RCA DRD420E I am only getting the odd transponders to come in. I tried hooking up a different SAT receiver and all transponders came in, odd and even. Does something have to be set with the RCA receivers in the menu or is it a bad piece.
|
|
Post 2 made on Thursday December 12, 2002 at 13:32 |
quest51459 Founding Member |
Joined: Posts: | September 2001 197 |
|
|
|
Post 3 made on Thursday December 12, 2002 at 15:37 |
Shoe Founding Member |
Joined: Posts: | August 2001 1,385 |
|
|
|
Post 4 made on Friday December 13, 2002 at 17:37 |
Matt Founding Member |
Joined: Posts: | August 2001 1,802 |
|
|
This is probably due to the length of the wire from your dish to your multiswitch.
|
|
Post 5 made on Saturday December 14, 2002 at 02:30 |
Theater Builders Long Time Member |
Joined: Posts: | November 2002 43 |
|
|
Is the proper type of dish selected in the setup menu, for the unit that does not work? What kind of dish and multi switch are you using?
|
|
Post 6 made on Saturday December 14, 2002 at 07:14 |
glaro Founding Member |
Joined: Posts: | February 2002 101 |
|
|
|
Post 7 made on Saturday December 14, 2002 at 16:10 |
Ernie Bornn-Gilman Yes, That Ernie! |
Joined: Posts: | December 2001 30,104 |
|
|
all of the above. maybe.
If you are only using one receiver, with one LNB cable, the multiswitch is, well, not even in the system! So it probably is not at fault, but the receiver is bad.
If you are using a multiswitch, let us know.
|
A good answer is easier with a clear question giving the make and model of everything. "The biggest problem in communication is the illusion that it has taken place." -- G. “Bernie” Shaw |
|
Post 8 made on Saturday December 14, 2002 at 19:02 |
Matt Founding Member |
Joined: Posts: | August 2001 1,802 |
|
|
Try a soft reset of the unit. Press power and UP cursor on the front panel at the same time. Hold for three seconds, and then turn on.
|
|
Post 9 made on Monday December 16, 2002 at 21:52 |
I'm about linn Lurking Member |
Joined: Posts: | December 2002 9 |
|
|
Bad reciever i doubt!!! bad multiswitch yes do not try to split dss signal with any kind of splitter!!!!
|
|
Post 10 made on Tuesday December 17, 2002 at 07:20 |
glaro Founding Member |
Joined: Posts: | February 2002 101 |
|
|
the key is that you put another reciever on that same line and it was getting both odd and even--did you try putting the rca somewhere else and see if the problem follows. the reciever puts out 18v for the odd transponders and 13v for when it needs an even transponder --very likely that the reciever is not putting out 13v-- could likely be bad reciever dude
|
|
Post 11 made on Tuesday December 17, 2002 at 13:20 |
Matt Founding Member |
Joined: Posts: | August 2001 1,802 |
|
|
Are you using a multiswitch?
|
|
Post 12 made on Tuesday December 17, 2002 at 13:35 |
primo Long Time Member |
Joined: Posts: | June 2002 126 |
|
|
CHECK YOUR FITTINGS....I had this problem turned out to be a short in the fitting.
or a short in the multiswitch.
primo
|
|
Post 13 made on Saturday December 21, 2002 at 15:30 |
Victor ciccarone Lurking Member |
Joined: Posts: | December 2002 5 |
|
|
I have seen this as well with a bad LNB.
If any other effort has faild try a new LNB
VR Audio Systems LLC Phoenix, Arizona
|
|
Post 14 made on Sunday December 29, 2002 at 18:12 |
NY hifi Long Time Member |
Joined: Posts: | November 2002 43 |
|
|
There are ALOT of variables you must check to determine what the problem is. Check each fitting. Use a flashlight and look inside of each RG6 connector. Check any barrels you may have, and sometimes a staple driven to hard into the cable will do this. TROUBLE SHOOT EVERYTHING
|
|
Post 15 made on Monday December 30, 2002 at 06:58 |
Cruz2002 Long Time Member |
Joined: Posts: | December 2002 14 |
|
|
I just went through three (yes, THREE!) of the RCA DRD485RG's - all of them had issues with even transponders not working properly. I've checked voltage outputs for both even and odd transponders on the RCA's (in the 13 and 19 volt ranges even when the signal is jumping from 97 to zero and back again). I'm running off of a simple multiswitch - the installers moved me to a different port - same issues (no one else in my building has complained of problems, but then again they don't have RCA units). Plugged in an older RCA to the same feed and it worked fine - plugged in a cheap Samsung as a temporary fix, and it seems to be fine so far. Looks like Thomson / RCA has some issues to deal with (oh, and their on-line support hasn't responded to my emails for the past week and a half). Looks like they don't want my business very much.
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|