Your Universal Remote Control Center
RemoteCentral.com
Complete Control by URC Forum - View Post
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Page 2 of 2
Topic:
Lutron Lamp DImmer + MX 900
This thread has 21 replies. Displaying posts 16 through 22.
Post 16 made on Sunday October 14, 2012 at 16:13
tweeterguy
Loyal Member
Joined:
Posts:
June 2005
7,713
On October 14, 2012 at 14:58, Lowhz said...
You need to put a dummy RF base into the program so that it 'enables' RF selection for the lighting devices, even if everything is IR controlled.

I'm talking about in the stand alone mx editor...by going into RF setup tab and setting the receiver ID and setting the lighting device to be set to RF and assigned to that ID.
OP | Post 17 made on Sunday October 14, 2012 at 20:22
Jrod730
Long Time Member
Joined:
Posts:
October 2012
11
Honestly, I bought the remote off of eBay. So all I know is that is a MX-900 Genesis. Is there a way I can figure out what frequency the remote is? I'll let you know in a bit how loading a new config works.
OP | Post 18 made on Sunday October 14, 2012 at 20:32
Jrod730
Long Time Member
Joined:
Posts:
October 2012
11
On October 14, 2012 at 16:13, tweeterguy said...
I'm talking about in the stand alone mx editor...by going into RF setup tab and setting the receiver ID and setting the lighting device to be set to RF and assigned to that ID.

I can't use standalone because I already loaded a remote setup from CCP. It says since I used a newer version (CCP) I cannot load anything from the standalone to my remote.
OP | Post 19 made on Sunday October 14, 2012 at 20:39
Jrod730
Long Time Member
Joined:
Posts:
October 2012
11
Ok I used the dummy base station. I used a config with onlly lights. Set up lights by using URC lighting, and used auto adress in the IR database of the CCP. I held the dimmer's rectangular button in the down direction for 10 seconds, then press the "on" button on the remote, and continued to hold both the dimmer and the remote. The lights just crawled down the dimmer for a while and didn't stop until I let go.
Post 20 made on Sunday October 14, 2012 at 23:36
goldenzrule
Loyal Member
Joined:
Posts:
July 2007
8,439
Do not press the down button. Press the main light button.
OP | Post 21 made on Friday October 19, 2012 at 23:06
Jrod730
Long Time Member
Joined:
Posts:
October 2012
11
Found the dimmer instructions in the URC Control Room. I reset the dimmer and did a hard reset on my remote. I still cannot address the dimmer. Does the CCP requiring me to choose a base station have anything to do with this? If so, is there a way around that? This is really frustrating me at this point.
Post 22 made on Saturday October 20, 2012 at 10:45
kgossen
Super Member
Joined:
Posts:
March 2008
3,026
How old is the 900?
"Quality isn't expensive, it's Priceless!"
Page 2 of 2


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse