Your Universal Remote Control Center
RemoteCentral.com
HDTV Reception Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Install new DirecTV 5 LNB Dish...
This thread has 4 replies. Displaying all posts.
Post 1 made on Saturday January 7, 2006 at 00:03
jfetter
Founding Member
Joined:
Posts:
December 2001
41
OK, you may find this slightly amusing...

I purchased a new Toshiba 56" 1080P DLP a few months back in preparation for going HD. My plan is to watch the entire 2006 World Cup in HD since we're not going to Germany to see it first hand. So I call DirecTV, I did my homework, I know if I replace my existing 2 LNB with a new dish and go HD, they are going to give me a 3 LNB (we don't get HD locals over Sat until May) which means they'll simply replace it again in a few months with what I want now, a 5 LNB dish.

So I try and work a deal, after all, I have been a subsriber for 8 years now, they seem to want to make me happy nowadays. No matter how hard I push, it seems they simply can't give me the 5 LNB now because they don't have enough to supply the markets where they DO have local HD channels over Sat. So I hang up, look online and in less than 5 minutes, purchase a 5 LNB and H20 MPEG 4 compatible receiver over the internet. 4 days later, it's in my livingroom.

I call DirecTV again, my 2 LNB dish was damaged in one of the Hurricanes this past summer, I figure they can turn me on to an installer and if they give me a difficult time, I can use the damaged dish (held together with duct tape) as a great excuse. To my surprise (and embarrassment), they tell me they'd love to help but since they dont yet have the 5 LNB's in my market, the installers wont know how to install them! The guy wishes me luck and appologizes, I can't really fault them as I went and purchased the hardware on my own.

So, I have mounted my own 2 LNB dish a few times, seems quite simple but I do understand with 5 satellites, I now have to worry about tilt angle when I mount this one. My question to those that have installed these is this, how hard is it, if I get the mounting mast fastened and plumb (using the included ball-level) and set the elevation and tilt per the settings for my zip code, can I expect to rotate to the correct azimuth usuing a compass and get a good signal (assuming I set the 110/119 degree LNB correctly - position 2 for me)?

I know the signal strength meter in the receiver isn't a good way to do this, and IF necessary I'll buy the signal strength meter but I figure as tightly manufactured as this new mounting base is (quite a fine mounting system), shouldn't it be as simple as getting the settings dialed in properly and rotating until I get the stongest signal?

I'd appreciate any help...

Thanks,

JFetter
Post 2 made on Saturday January 7, 2006 at 09:04
dugan
Long Time Member
Joined:
Posts:
December 2005
69
i would say yes. try the hope and poke system with walkie talkies and line up 110/119. i don't do a lot of dish's anymore i was certified directtv and dish a few years ago so i'll check my sources. sounds like i'll have to find out anyway. dave
audio/video dave
Post 3 made on Saturday January 7, 2006 at 09:53
KiKi
Lurking Member
Joined:
Posts:
December 2005
7
The install should not be to hard. Read and follow all instructions. Two
people with walkie talkies will make the job much easier. A compass will come in very handy as well. If you live in a hurricane zone as I do, mounting this dish securely is very important due to its larger size and wind load. I have yet to install one myself as they are not available in the South Florida area, but if you have any further questions post again and I'll try to help
OP | Post 4 made on Saturday January 7, 2006 at 17:21
jfetter
Founding Member
Joined:
Posts:
December 2001
41
Thanks for the support, I installed the dish myself, setting the elevation and tilt carefully per the settings for my zip code. I took extra special care to get the mounting post plumb and firmly attached with 4 concrete bolts. All that was really required was rotating to find the azimuth using 101 and then fine tuning the elevation again using 119. Though they tell you not to use the receivers strength meter, the end result was strong signals to the existing 2 Ultimate TV's and wahat appears to be all active satellites being detected by the new H20.

BTW, the harware on this new dish is outstanding! Fine tuning adjustments for both elevation and azimuth plus very strong, well built and engineered assembly...

Jack
Post 5 made on Monday January 9, 2006 at 10:47
KiKi
Lurking Member
Joined:
Posts:
December 2005
7
Glad to hear all went well for you.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse