Your Universal Remote Control Center
RemoteCentral.com
Complete Control by URC Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Newbie question about URC
This thread has 8 replies. Displaying all posts.
Post 1 made on Friday September 29, 2006 at 23:32
Chivalrousthief
Lurking Member
Joined:
Posts:
September 2006
4
So, there i was...

Is there any way to get codes that are not in the URC data base into a URC (other than learning them)? Is there any way to Adapt the hex codes that the Prontos use?
Post 2 made on Friday September 29, 2006 at 23:51
dpinc
Long Time Member
Joined:
Posts:
August 2004
196
Which urc? Yes you can with the MX editor universal browser.
Derek Pinc
OP | Post 3 made on Friday September 29, 2006 at 23:57
Chivalrousthief
Lurking Member
Joined:
Posts:
September 2006
4
I have the Mx-850...what is this universal browser?
Post 4 made on Saturday September 30, 2006 at 03:40
JonW747
Active Member
Joined:
Posts:
September 2006
621
It's the button next to the satellite dish. Dunno why it's not a menu option.

You can open a .CCF file from a Pronto with it. When you find a panel with a button with a learned code, you click the button, and then drag and drop the word "learned data" over on to an MX-850 button. You can then basically import any hex code in to your MX-850 by first using a pronto editor and saving out a .CCF file. The browser doesn't support the newer pronto .PCF format though.
Post 5 made on Saturday September 30, 2006 at 20:58
PChek
Long Time Member
Joined:
Posts:
May 2003
206
But you don't need to drag the words "learned data." You can just click and drag the button itself. As long is it does say 'learned data,' the data will be imported.
Pchek
Post 6 made on Saturday September 30, 2006 at 22:00
shnakz69
Active Member
Joined:
Posts:
February 2006
737
hex input is available only in the mx3000 right now via the universal browser... and if the hex code is not in the right format then you can use the makehex program to convert it..
OP | Post 7 made on Saturday September 30, 2006 at 22:49
Chivalrousthief
Lurking Member
Joined:
Posts:
September 2006
4
how do i get it to say 'learned data'?? right now it only says 'ir data'
Post 8 made on Sunday October 1, 2006 at 02:26
PChek
Long Time Member
Joined:
Posts:
May 2003
206
Use MakeHex and hex2ccf to generate a .ccf file in which all buttons are learned data. Both are available in the files section of this site. See this thread in which I began to learn about it, or just do a search for other posts by johnsfine.
Pchek
Post 9 made on Sunday October 1, 2006 at 03:13
JonW747
Active Member
Joined:
Posts:
September 2006
621
On September 30, 2006 at 20:58, PChek said...
But you don't need to drag the words "learned data."
You can just click and drag the button itself. As long
is it does say 'learned data,' the data will be
imported.

Ahh, you're right! I could swear that didn't use to work.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse